Product Description
Chrysler Sebring 2007-2010 Sedan Gas Door Trim with Two Crease Contours (GC47780)
What sets GC47780 apart is its shape. The catalog note says it has "Two crease contours," so this isn't a plain flat plate; the stainless has two creases formed into it. Look at the product photos to see how those creases run and where they sit on the door. The part is listed for the 2007-2010 Chrysler Sebring 4-door sedan, four model years on a single Fitment row.
It's made from one piece of 304 stainless steel, 26 gauge, polished, in the USA, and it mounts to the fuel door with 3M automotive-grade acrylic foam tape.
On the Sebring, this trim is not a replacement cap and not a replacement part. The 2007-2010 Sebring's own fuel door has to be in place, because the polished stainless overlays it.
Why the contours matter when installing
A trim with formed creases has one right orientation, so the dry fit matters more than it would with a flat plate. Study the photos first so you know which way it goes. Then, with the liner still on, set the trim on the closed door and move it until it matches the photos and the paint margin around the edges is even. If it doesn't seem to sit right in any position, stop and call before peeling the liner. Once the tape touches paint, repositioning is much harder.
Other Sebring sedan trim
Three parts are cross-listed. LP47780 is a one-piece license plate bezel. RD47780 is a one-piece rear deck accent, 1.125 inches wide. RI47780 is a two-piece roof insert trim. Each has its own listing with photos and install notes, and any of them can be paired with this gas door piece.
Holding power
GC47780 installs directly over the existing surface; no drilling is needed. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle. Since the tape bonds to paint, check the door for faded or flaking clear coat, chipped edges, or bubbles, and repair them before installing. The door should also close flush with the body.
Putting it on
Wash the door with soap and water, rinse, dry, and degrease until a clean cloth shows nothing. Do the contour dry fit described above, then mark the final position with painter's tape. Peel the liner, line the creases and edges up with your marks, and press firmly over the whole face, especially along the crease lines so the tape seats fully. Press again after a minute. Open the door slowly to check clearance. The Installation tab has more detail.
Finish
The polished 304 stainless reflects light brightly, and the contours give it some depth. At 26 gauge it remains thin on the door.
Care
Install on a dry, mild day and leave it dry overnight. Clean with mild soap and a soft cloth, and wipe away fuel drips.
For the Sebring fuel door trim, ring 877-752-3811 and quote GC47780; the UPC is listed on Specs.
GC47780 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | GC47780 |
| UPC | 691821716999 |
| Part type | Gas Door Cover Trim |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Coverage / notes | Two crease contours |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2007-2010 Chrysler Sebring |
| Not included | This is NOT a replacement gas cap or door; your existing gas door is required |
Fitment: GC47780
| Vehicle | Years | Body style |
|---|---|---|
| Chrysler Sebring | 2007-2010 | 4-door, Sedan |
Check your vehicle against every column here: year range, model, and body style all have to match. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2007-2010 Chrysler Sebring
- LP47780: 1-piece License Plate Bezel
- RD47780: 1-piece Rear Deck Accent
- RI47780: 2-piece Roof Insert Trim
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Gas Door Cover Trim
- Confirm your vehicle still has its original gas door. This trim mounts over it and does not replace it.
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: GC47780 Gas Door Cover Trim
Is GC47780 a replacement gas door?
No. It is not a replacement cap or replacement part. You must have the existing gas door to install this piece.
Is it flat?
No. The catalog notes it has two crease contours. Check the photos to see the shape.
Which Sebring fits?
The 2007-2010 Chrysler Sebring 4-door sedan.
What is it made of?
Polished 304 stainless steel, 26 gauge, made in the USA.
Does it need drilling?
No. It installs directly over the existing surface with 3M automotive-grade acrylic foam tape.
How long does the tape hold?
QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
