Product Description
Lincoln Navigator 2007-2014 License Bar with Logo Cut Out (LB47655)
LB47655 is the license bar QAA lists for the Lincoln Navigator 4-door SUV, model years 2007 through 2014. It has one distinguishing detail in the catalog: With Logo Cut Out. The bar runs above the rear license plate and has an opening shaped so the logo shows through rather than being covered.
Specs
One piece, cataloged as License Bar, Above plate accent Trim. Made in the USA from 26-gauge 304 stainless steel, polished to a mirror finish. Mounting is 3M automotive-grade acrylic foam tape, and it installs directly over the existing surface. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle. The sheet gives no width.
What to check on your Navigator
First, the year. The listing covers eight model years, 2007 to 2014; your records confirm yours. Second, the logo. The cutout is designed to frame it, so the logo should be in its original place. If it's been removed or moved, the opening will frame empty paint. Third, anything else around the plate. The catalog doesn't mention key access, a camera opening or other cutouts, so compare the photos with your liftgate. If any of these checks raises a question, call Quality Automotive Trims at 877-752-3811 and mention LB47655.
Using the cutout to place it
The logo opening is a ready-made alignment point. Clean the area first: wash, rinse, dry and wipe with rubbing alcohol, working carefully around the logo, where wax tends to build up along the edges. With the liner still on, set the bar in place and move it until the logo sits evenly inside the cutout. Check from behind the vehicle that the bar looks level. Mark both ends with painter's tape. Peel the liner, line it up again, and press firmly along the length and all around the opening. Wait a minute, then press once more. Close the liftgate gently for the first day. Temperature guidance is on the Installation tab.
Paint condition
On a Navigator from the early years of this range, the paint around the plate may show chips or worn clear coat. Tape needs a sound surface, so look closely before you install and fix any flaking first.
Pairing with the bezel
The only other part cross-listed for this Navigator is LP47655, a one-piece license plate bezel. The bezel frames the plate on all sides; this bar sits above it with its logo opening. Using both gives the plate area a frame and an accent line. Check the bezel listing's photos for its finish and fit before ordering both.
Why a cutout instead of a plain bar
A plain strip above the plate on a liftgate with a logo nearby would either sit awkwardly below it or cover part of it. A cutout keeps the logo visible and makes the bar look shaped for the vehicle. It also takes the guesswork out of centering.
Care
To clean the Navigator's license trim, use mild soap and water and dry with a soft towel; abrasive pads and gritty polish will mark it.
LB47655 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | LB47655 |
| UPC | 691821355549 |
| Part type | License Bar, Above plate accent Trim |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Coverage / notes | With Logo Cut Out |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2007-2014 Lincoln Navigator |
Fitment: LB47655
| Vehicle | Years | Body style |
|---|---|---|
| Lincoln Navigator | 2007-2014 | 4-door, SUV |
Check your vehicle against every column here: year range, model, and body style all have to match. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2007-2014 Lincoln Navigator
- LP47655: 1-piece License Plate Bezel
Check the body style on each listing; some kits are specific to one body style.
Installation tips: License Bar, Above plate accent Trim
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: LB47655 License Bar, Above plate accent Trim
Does LB47655 cover the logo?
No. It has a logo cut out so the logo stays visible.
Which Navigator years does it fit?
2007 through 2014, 4-door SUV.
What if my logo was removed?
The cutout would frame bare paint. Call 877-752-3811 before ordering.
How does it attach?
3M automotive-grade acrylic foam tape, directly over the existing surface. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
Is there a matching bezel?
LP47655, a license plate bezel, is listed for the same Navigator. Check its photos for finish.
