Product Description
Toyota 4Runner 2010-2015 Rear Bumper Trim, Polished Stainless (RB10177)
RB10177 is a one-piece rear bumper accent that QAA lists for the 4-door Toyota 4Runner SUV from 2010 to 2015. It is cut from 304 stainless steel, polished to a mirror, made in the USA, and installed with 3M tape.
A standalone piece
Unlike many vehicles in the catalog, this 4Runner record has no other QAA kits linked to it. RB10177 is a single accent for the back of the truck, and it does not depend on any other trim to look finished.
Fitment years
2010, 2011, 2012, 2013, 2014, and 2015, 4-door SUV. If your 4Runner is newer or older, this listing does not cover it.
What it does
A rear bumper accent is a polished strip that adheres to the rear bumper surface. It brings a line of brightwork to the back of the 4Runner, the view traffic behind you sees. The original bumper stays in place and is not altered.
Steel, not plating
The accent is 26-gauge 304 stainless with a mirror polish. Because the finish is part of the steel, there is no plated layer to blister or peel, which matters on a part that sits low and close to road spray.
How it attaches
3M automotive-grade acrylic foam tape is used, and the piece goes over the existing surface. No bumper removal. QAA states the tape will hold for a lifetime without causing damage to the vehicle surface.
Cleaning an SUV bumper
An SUV's back end picks up mud, dust, and road film. Wash the bumper thoroughly, dry it, and wipe the mounting area with a residue-free cleaner. If you use tire shine or plastic dressing, make sure none of it is on the mounting area, because silicone residue prevents tape from bonding. Repair any chipped or peeling paint first.
Fitting it
Work on a dry, mild day. With the liner still on, hold the accent in place and compare its position with the product photos. Step back and check that it is level and centered. When you are satisfied, peel the liner and press firmly from the middle out to both ends. Avoid washing or off-road use for a few days while the bond settles. The Installation tab has full steps.
After installation
Rinse grit off before wiping, especially after dirt roads, then wash with mild soap and dry with a soft towel. Abrasive pads will scratch the mirror finish.
Why owners choose it
A bright strip at the rear is a small detail that makes a well-kept 4Runner look finished from behind, and it can be done in a few minutes in the driveway.
Before ordering
Confirm the year on your registration.
Getting it level
A one-piece accent on a wide rear bumper shows any tilt immediately. During the dry-fit, measure from each end of the strip to a fixed point on the bumper and adjust until it sits where the photos show it. A strip of masking tape as a guide line makes it easy to press the accent down exactly where you tested it.
Part details
4Runner bumper trim RB10177 carries UPC 691821514809. Quality Automotive Trims answers questions at 877-752-3811.
RB10177 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | RB10177 |
| UPC | 691821514809 |
| Part type | Rear Bumper Trim Accent |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2010-2015 Toyota 4Runner |
Fitment: RB10177
| Vehicle | Years | Body style |
|---|---|---|
| Toyota 4Runner | 2010-2015 | 4-door, SUV |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Installation tips: Rear Bumper Trim Accent
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: RB10177 Rear Bumper Trim Accent
Which 4Runner does RB10177 fit?
The 4-door Toyota 4Runner SUV, model years 2010 through 2015.
How many pieces?
One.
Do I have to remove the bumper?
No. It mounts with 3M automotive-grade acrylic foam tape over the existing surface.
Is it chrome?
No. It is mirror-polished 304 stainless steel, made in the USA.
Are other QAA kits linked to this 4Runner?
None are linked on this record. Call 877-752-3811 to ask about other trim.
