Product Description
Dodge Charger 2006-2007 Sedan Stainless Gas Door Cover (GC46910)
The fitment window on this listing is short: just two model years. GC46910 is made for the 2006 and 2007 Dodge Charger 4-door sedan, and that is the only row on its Fitment tab. If you drive a Charger, the very first thing to check is the model year, because a car from just outside that pair is not covered here.
Check the year against that range. If it reads 2006 or 2007, read on. If it doesn't, call us before ordering and we'll look at what fits instead.
For the 2006-2007 Charger, the cover is one polished 304 stainless piece, 26 gauge, made in the USA, and it mounts with 3M automotive-grade acrylic foam tape.
Equally important: GC46910 is not a replacement cap and not a replacement part. You MUST have the existing gas door to install this piece. It's a decorative cover for the door that's already on the Charger, so a cracked or missing door must be dealt with first.
Nothing else is cross-listed on this sheet. There are no pillar, rocker, or handle parts linked here, though that's a limit of this page rather than proof nothing else exists. Ask when you call if you're interested in more stainless for the car.
Here's how the installation goes. Because GC46910 installs directly over the existing surface, you won't drill anything. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle. The weak point in any taped part is the paint below it, so give the gas door a careful look first. If you see the clear coat lifting or going cloudy, chips along the edge, or small bubbles, have that repaired before the trim goes on. The door should also latch firmly and sit flush.
When the paint is ready, wash the door with soapy water and rinse it, then dry it fully. A degreaser wipe comes next; keep at it until the cloth stays clean. Without removing the liner, hold the cover against the closed door and slide it until the band of paint showing around it is uniform. Ask someone to check from a few steps back if you can, and mark the final spot with small pieces of painter's tape. Remove the liner, line the cover up with the tape, and set it in one steady motion. Press hard across the entire surface, especially the edges, and after a minute or so press it all again. Open the door carefully to make sure it swings freely. The Installation tab lays this out in more detail.
Polished 304 stainless gives a bright, mirror-like finish, and the thin 26 gauge cover sits close to the Charger's door.
For best results, install on a mild, dry day and let the tape set overnight before the car sees water. Afterward, a soft cloth and gentle soap are all it needs, along with a wipe whenever fuel splashes on it.
For the Charger fuel door trim, ring 877-752-3811 and give GC46910; the Specs tab has the UPC.
GC46910 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | GC46910 |
| UPC | 691821339822 |
| Part type | Gas Door Cover Trim |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2006-2007 Dodge Charger |
| Not included | This is NOT a replacement gas cap or door; your existing gas door is required |
Fitment: GC46910
| Vehicle | Years | Body style |
|---|---|---|
| Dodge Charger | 2006-2007 | 4-door, Sedan |
Check your vehicle against every column here: year range, model, and body style all have to match. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Installation tips: Gas Door Cover Trim
- Confirm your vehicle still has its original gas door. This trim mounts over it and does not replace it.
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: GC46910 Gas Door Cover Trim
Is GC46910 a replacement gas door?
No. It is not a replacement cap or replacement part. You must have the existing gas door to install this piece.
Which Charger years fit?
Only the 2006 and 2007 Dodge Charger 4-door sedan.
What is it made of?
Polished 304 stainless steel, 26 gauge, made in the USA.
Will I need to drill?
No. It installs directly over the existing surface with 3M automotive-grade acrylic foam tape.
How long does the tape hold?
QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
