Product Description
Dodge Neon Coupe 1995-1998 Upper Rocker Kit, 6 Pieces, 7" Down from the Molding (TH35914)
TH35914 is a six-piece polished stainless steel Upper Kit for the 1995-1998 Dodge Neon 2-door coupe. It's 7" wide and "Spans from the bottom of the molding DOWN to the specified width."
Coupe or sedan
The Neon has two linked kits with the same 7" width and the same span note. TH35914, this one, is six pieces for the 2-door coupe. TH35915 is eight pieces for the 4-door sedan. Order by door count.
A tall Upper Kit
Seven inches is a generous band for an Upper Kit. It starts under the molding and runs down 7", then stops. Whether any paint shows below it depends on your car's molding-to-door-bottom distance, which the record doesn't give. Measure it. If it's close to 7", the steel will reach nearly to the bottom; if it's more, a strip of paint will remain beneath.
Six pieces on two doors
There are more pieces than doors, and the record doesn't say where the extras go. Use the photos to sort them by shape, and label each liner before cleaning.
Steel and tape
The Neon coupe's six pieces are USA-made polished 26 gauge 304 stainless steel, fixed over the paint already there with 3M automotive-grade acrylic foam tape. Per QAA, that tape will hold for a lifetime and causes no damage.
A visible lower edge
Because an Upper Kit ends on paint, its lower edge needs to be straight. Measure 7" down from the molding at several points per door and lay painter's tape along the marks as a guide. Keep it there until the side is finished.
Molding
Each piece's top edge tucks under the molding. Press along the molding on both doors and reattach any loose sections before prep.
Prep
Wash, dry, then wipe the band with isopropyl alcohol until a clean cloth stays clean. Repair chips within the band.
Fitting
Dry-fit each piece against the guide. Peel a few inches, set the top edge, press, and keep going as the liner comes off. Firm pressure at the end.
Long doors
A helper holding the far end off the paint keeps a long piece from grabbing early.
Matching
Measure the Neon positions and keep them consistent.
Care
The Neon waits a day before washing.
Door swing
After each door piece goes on, swing the door through its full arc and look at the hinge side and the trailing edge for contact.
Questions to settle before ordering
Is it the coupe? Is the molding on both doors intact? Does the 7" band look right with painter's tape on the car? If any answer is unclear, call 877-752-3811 with a photo; it's quicker than a return.
Supplies
For the Neon, clean with car soap and isopropyl alcohol on lint-free cloths, mark the pieces with painter's tape and a marker, measure with a tape measure, and keep a plastic trim tool nearby. Work in shade on a dry, mild day.
The six-piece Neon set TH35914 has UPC 691821574391; ring 877-752-3811 with questions.
TH35914 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | TH35914 |
| UPC | 691821574391 |
| Part type | Rocker Panel Trim, Upper Kit |
| Pieces in kit | 6 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 7" |
| Coverage / notes | Spans from the bottom of the molding DOWN to the specified width |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 1995-1998 Dodge Neon |
Fitment: TH35914
| Vehicle | Years | Body style |
|---|---|---|
| Dodge Neon | 1995-1998 | 2-door, Coupe |
Fitment is listed exactly as QAA catalogs it. Confirm the body style as well as the year and model. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 1995-1998 Dodge Neon
- TH35915: 8-piece Rocker Panel Trim, Upper Kit
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Rocker Panel Trim, Upper Kit
- Unpack all 6 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: TH35914 Rocker Panel Trim, Upper Kit
Does TH35914 fit the Neon sedan?
No. It's tagged 2-door coupe. The sedan kit is TH35915.
How far down does it go?
7" from the bottom of the molding.
How many pieces?
Six.
Which years?
1995-1998 Dodge Neon.
