Product Description
Chevrolet Blazer 1998-2000 Two-Door, Molding, No Flares: 8-Piece Lower Rocker Trim, 5" (TH38192)
TH38192 is the two-door Blazer half of a linked pair for 1998-2000. Its tag reads "2-door, SUV, w/ Molding, NO flares." The kit is eight pieces of polished stainless steel, a Rocker Panel Trim Lower Kit 5" tall, set "from the bottom of the door UP to the specified width."
Two kits, two differences
The linked TH38193 is also eight pieces and 5", but its tag is "4-door, SUV w/ Molding, w/ Flares." So the pair differs on two counts at once: door count and flares. The record doesn't offer a two-door kit with flares or a four-door kit without them. If your Blazer is one of those combinations, don't assume either kit fits. Call 877-752-3811 with photos and we'll check.
Three things to confirm
- Two doors.
- Molding along the sides.
- The Blazer must have no flares at the wheel openings.
All three, plus a year from 1998 to 2000, match this record.
Height and placement
The steel's lower edge follows the bottom of the door, and the top edge sits five inches above it. With molding on the truck, check where it sits compared with that five-inch line before you order.
Eight pieces on a two-door
The data gives the count but not the layout. Lay the pieces out, compare them with the product photos, and work out where each goes before any liner comes off. If a piece doesn't have a home, stop and call.
The material
The Blazer's eight pieces are polished 26 gauge 304 stainless, produced in the USA, and attached over the existing surface with 3M automotive-grade acrylic foam tape. According to QAA, the tape will hold for a lifetime without causing damage to the SUV.
Door bottoms
Run a hand along the lower edge of each long door. Any chip, bubble or flaking paint there should be repaired and cured before trim goes over it.
Putting it on
- Clean and dry the Blazer's lower body, then wipe it with isopropyl alcohol.
- Write each piece's position on its liner.
- Dry-fit with painter's tape, lower edge on the door bottom.
- Peel a few inches of liner, press the end, and work along.
- Bear down firmly on each piece.
Near the wheel openings
Without flares, pieces that end near the wheel openings sit on plain body. Make sure their ends lie flat during the dry run.
Swing test
Open each door through its full arc after installing and watch the trim edge at the bottom.
Supplies
Gather a tape measure, painter's tape, a marker, car soap, isopropyl alcohol and lint-free towels for the Blazer, and choose a dry, mild day in the shade.
Care
Hold off washing for a day, then use mild soap and soft cloths.
Blazer spacing
Measure each piece's distance from the door edges and wheel openings and keep it consistent.
When you call
Have the year, a side photo showing the molding, and close-ups of the wheel openings. That lets us confirm the two-door, no-flare tag quickly.
Two-door Blazer kit TH38192, UPC 691821425129. Quality Automotive Trims, 877-752-3811.
TH38192 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | TH38192 |
| UPC | 691821425129 |
| Part type | Rocker Panel Trim, Lower Kit |
| Pieces in kit | 8 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 5" |
| Coverage / notes | Spans from the bottom of the door UP to the specified width |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 1998-2000 Chevrolet Blazer |
Fitment: TH38192
| Vehicle | Years | Body style |
|---|---|---|
| Chevrolet Blazer | 1998-2000 | 2-door, SUV, w/ Molding, NO flares |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 1998-2000 Chevrolet Blazer
- TH38193: 8-piece Rocker Panel Trim, Lower Kit
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Rocker Panel Trim, Lower Kit
- Unpack all 8 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: TH38192 Rocker Panel Trim, Lower Kit
Which Blazer is TH38192 for?
1998-2000 Chevrolet Blazer 2-door SUV with molding and no flares.
I have a four-door Blazer with flares.
The linked TH38193 is tagged for that.
What about a two-door with flares?
No linked kit is tagged that way. Call 877-752-3811 with photos.
How tall and how many pieces?
5" tall, eight pieces.
