Product Description
Polished Stainless Marker Light Trim, 2 Pieces, for the 2006-2009 Hummer H3 (HV46305)
HV46305 is a two-piece marker light trim for the Hummer H3 4-door SUV, model years 2006 through 2009. It is polished 26-gauge 304 stainless steel, made in the USA, and mounts with 3M automotive-grade acrylic foam tape directly over the existing surface.
A short listing
The catalog gives the part type, the piece count and the material, and nothing more: no note on which marker lights the trim is for, no ring or surround description, and no removal instruction. That means the product photos carry most of the information. Look at them carefully, compare them with the marker lights on your H3, and call if they don't look the same. If a marker light has been replaced with an aftermarket unit, the trim may not line up.
Two pieces
The catalog doesn't say how the two pieces are split. The photos will show you, and sorting the pieces against them before you install is the easiest way to avoid mixing them up.
Installing near a lens
QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle. No drilling is needed. Because marker light trim sits beside a lens, take a little care:
- Clean the area with soap and water, then rubbing alcohol, and let it dry.
- Keep fingers off the tape and the lens while positioning.
- Dry-fit each piece with the liner on to confirm it frames the light evenly.
- Peel and press firmly around the whole piece.
- Check afterward that the trim doesn't cover any part of the light you want visible.
The catalog doesn't mention removing the marker lights for this kit. If the photos suggest the trim sits under the edge of the lamp, or if anything is unclear, call before you start. The Installation tab has general guidance.
Other H3 parts
The H3 sheet lists thirteen other parts, including HV46306, a one-piece grille and front accent noted "Z-Grille Cover"; HV46302, a two-piece hood accent; HV46303, a nine-piece hood vent trim; and HV46311, a two-piece rear window trim accent. Check each listing's photos before ordering.
A small detail that rounds out the look
Marker light trim is one of the smaller pieces, but it helps if stainless is already on the H3, carrying the same finish to another spot. It's also a quick job: two pieces, a clean surface, and a few minutes of careful alignment. If you're building up the truck in stages, it's an easy one to slot in between larger kits.
Material
Polished 304 stainless has its mirror shine in the steel, not in a plating layer. 26 gauge is thin, so the trim sits low around the lamp.
Care
Wash with mild soap and water and dry with a soft towel. Avoid abrasive products, which can scratch both the stainless and the lens.
Fitment
Hummer H3, 4-door SUV, 2006-2009, no other restrictions. Confirm the H3 was built in one of the years listed.
For the H3 marker light accents, call 877-752-3811 and cite HV46305; Specs has the UPC.
HV46305 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | HV46305 |
| UPC | 691821362936 |
| Part type | Marker Light Trim |
| Pieces in kit | 2 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2006-2009 Hummer H3 |
Fitment: HV46305
| Vehicle | Years | Body style |
|---|---|---|
| Hummer H3 | 2006-2009 | 4-door, SUV |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2006-2009 Hummer H3
- HV46301: 4-piece Rocker Panel Trim, Lower Kit
- HV46302: 2-piece Hood Accent Trim
- HV46303: 9-piece Hood Vent Trim
- HV46304: 4-piece Body Molding Insert Trim Kit
- HV46306: 1-piece Grille Accent
- HV46307: 6-piece Letter Graphics
- HV46308: 2-piece Letter Graphics
- HV46309: 6-piece Wheel Well Accent Trim
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Marker Light Trim
- Unpack all 2 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: HV46305 Marker Light Trim
What is HV46305?
A two-piece polished stainless marker light trim for the 2006-2009 Hummer H3 4-door SUV.
Which marker lights does it fit?
The catalog doesn't say. The product photos show it installed, or call 877-752-3811.
Do I need to remove the marker lights?
The catalog doesn't mention removal for this kit. Check the photos and call if unsure.
How does it attach?
With 3M automotive-grade acrylic foam tape. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
How many pieces?
Two.
