Product Description
Ford Fusion 2006-2009 License Bar with Logo Cut Out, Polished Stainless (LB46390)
LB46390 is a license bar shaped around the emblem. The catalog note reads With Logo Cut Out, and that opening is what separates it from a plain strip: the bar runs above the rear plate of a Ford Fusion sedan, and the logo stays visible through it. The fitment is one row, the Ford Fusion 4-door sedan, model years 2006 through 2009.
At a glance
- For the Fusion: a single License Bar, Above plate accent Trim
- Polished 26-gauge 304 stainless steel, made in the USA
- With Logo Cut Out
- 3M automotive-grade acrylic foam tape, installs directly over the existing surface
- No width listed
For the 2006-2009 Fusion license trim, QAA says the tape holds for a lifetime without damaging the vehicle's surface.
Before you order
Check the year: 2006, 2007, 2008 or 2009. Then look at the trunk lid. The logo cut out only works if the emblem is where the photos show it. If a previous owner removed the emblem or a body shop moved it, the opening will frame bare paint. In that case, or if anything else on the trunk sits in the bar's path, call Quality Automotive Trims at 877-752-3811 with LB46390 before ordering.
Placement made simple
A logo opening gives you a built-in reference point. Wash, dry and alcohol-wipe the area, paying attention to the edges around the emblem, where wax and grime tend to collect. Hold the bar in place with the liner on and slide it until the emblem sits evenly in the cutout. Check from behind the car that it's level, then mark both ends with painter's tape. Peel the liner, line up the cutout and the marks, and press firmly along the length and around the opening. Press again a minute later. Close the trunk gently for the first day. The Installation tab covers temperature.
On an older car
Paint on a Fusion from these years may have chips, faded clear coat or adhesive residue near the plate. The tape needs sound, clean paint, so fix any flaking finish first and clean the Fusion thoroughly.
Three related Fusion parts
The sheet lists LP46390, a one-piece license plate bezel at 7.88"; ET46390, a one-piece exhaust trim package at 2.48"; and FV46390, a two-piece front vent trim. The bezel frames the plate, while this bar sits above it, so the two can be used together. Check each listing's photos for its finish and fit.
Bar or bezel?
Buyers sometimes mix up the two. A license plate bezel surrounds the plate on all sides. A license bar is a single strip above it. LP46390 is listed at 7.88", while the catalog gives no width for this bar, so the photos are the way to compare them. Using both gives the plate area a frame plus an accent line, but either works alone. If you plan to use both, compare the two listings' photos side by side to see how they sit together before ordering.
Clean it with mild soap, water and a soft towel.
LB46390 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | LB46390 |
| UPC | 691821462162 |
| Part type | License Bar, Above plate accent Trim |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Coverage / notes | With Logo Cut Out |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2006-2009 Ford Fusion |
Fitment: LB46390
| Vehicle | Years | Body style |
|---|---|---|
| Ford Fusion | 2006-2009 | 4-door, Sedan |
Check your vehicle against every column here: year range, model, and body style all have to match. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2006-2009 Ford Fusion
- ET46390: 1-piece Exhaust Trim Package
- FV46390: 2-piece Front Vent Trim
- LP46390: 1-piece License Plate Bezel
Check the body style on each listing; some kits are specific to one body style.
Installation tips: License Bar, Above plate accent Trim
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: LB46390 License Bar, Above plate accent Trim
Does LB46390 have a logo opening?
Yes. The catalog notes With Logo Cut Out.
Which Fusion years does it fit?
2006 through 2009, 4-door sedan.
What if my emblem has been removed?
The cutout would frame bare paint. Call 877-752-3811 before ordering.
How does it attach?
3M automotive-grade acrylic foam tape, directly over the existing surface. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
How wide is it?
No width is listed.
