Product Description
Ford Fusion Sedan 2006-2009 Stainless Exhaust Trim, 1 Piece, 2.48" Wide (ET46390)
ET46390 is a single polished stainless exhaust trim piece for the Ford Fusion 4-door sedan, model years 2006 through 2009. It's listed at 2.48" wide, made in the USA from 304 stainless steel at 26 gauge, and mounts with 3M automotive-grade acrylic foam tape.
One piece, one measurement
The catalog gives a width of 2.48" and no length. It also doesn't describe exactly where on the car the piece sits. Since it mounts with foam tape directly over the existing surface, it's an exterior accent rather than a part of the exhaust system. Use the product photos to see the shape and location, and call us if you'd like to confirm it matches your Fusion.
Fitment
Ford Fusion, 2006-2009, 4-door Sedan. One row, four model years. The Fitment tab lists it.
Rear-end companions
The same Fusion has related trim on this sheet, including two pieces for the back of the car:
- LB46390, a license bar above the plate, with logo cut out.
- LP46390, a license plate bezel at 7.88.
- FV46390, a two-piece front vent trim.
With the license bar and bezel too, the exhaust trim carries polished steel across the Fusion's rear.
Material
Polished 304 stainless steel, 26 gauge. Bright because the metal itself is polished.
Mounting
It installs directly over the existing surface. No drilling. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
Clean the area properly
The lower rear of a car picks up road grime and exhaust residue, and tape won't bond through either. Wait until the car is fully cool. Wash and rinse the area, then degrease, repeating until a clean cloth comes away clean. Check that the surface is sound. Dry completely.
Placing it
Hold the piece in position with the liner still on and look at it from behind the car. Check that it's level. Mark its ends with painter's tape. Peel, line up, and press firmly across the full piece, then again a minute later. The Installation tab has full prep.
Why a single accent
A single trim piece is a quick install, and at the back of the car it's in view of every driver behind you. It brightens the back without changing anything about how the car runs.
Ordering checklist
Confirm a 2006-2009 Fusion sedan, look at the photos for placement, and consider whether you'd like the license bar or bezel too.
Getting it level
A single piece has nothing beside it to compare against, so use the body lines. Measure from a nearby edge to each end of the piece and keep both numbers the same before pressing it down.
Conditions
Dry, mild weather; keep the car dry overnight.
Care
Mild soap and a soft cloth. The lower rear of a car gets dirty quickly, so a regular gentle wash keeps the polished face bright. Skip steel wool and scouring pads, which scratch stainless.
Questions
Call Quality Automotive Trims at 877-752-3811 and mention ET46390. The UPC is on the Specs tab.
ET46390 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | ET46390 |
| UPC | 691821708710 |
| Part type | Exhaust Trim Package |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 2.48" |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2006-2009 Ford Fusion |
Fitment: ET46390
| Vehicle | Years | Body style |
|---|---|---|
| Ford Fusion | 2006-2009 | 4-door, Sedan |
Check your vehicle against every column here: year range, model, and body style all have to match. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2006-2009 Ford Fusion
- FV46390: 2-piece Front Vent Trim
- LB46390: 1-piece License Bar, Above plate accent Trim
- LP46390: 1-piece License Plate Bezel
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Exhaust Trim Package
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: ET46390 Exhaust Trim Package
What does ET46390 fit?
The 2006-2009 Ford Fusion 4-door sedan.
How wide is it?
The catalog lists 2.48" width.
How many pieces?
One exhaust trim piece.
What is it made of?
Polished 304 stainless steel, 26 gauge, made in the USA.
Does it need drilling?
No. It installs directly over the existing surface with 3M automotive-grade acrylic foam tape.
How long does the tape hold?
QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
