Product Description
TH92036 Infiniti M30 1992-1994 Full Rocker Kit, Coupe & Convertible, 3.75", 10 Pieces
TH92036 is a ten-piece polished stainless steel Full Kit for the 1992-1994 Infiniti M30, tagged "2-door, Coupe, Convertible." It "Spans from the bottom of the molding to the bottom of the door," and the listed width is 3.75".
Ten pieces against six
The other M30 Full Kit, TH92035, shares the 3.75" width and the fitment but has six pieces and the note "Includes coverage between the wheel wells only." This listing carries no length note at all. The record doesn't say what the four further pieces here are for. Compare the photos of both listings, and if the layout still isn't clear, call 877-752-3811 before you order.
A narrow space to fill
3.75" between the molding and the door bottom doesn't leave much room for error. Measure carefully with a rigid ruler, at the front and rear of both doors. If any reading differs from 3.75" by more than a little, stop and send us the figures.
Two body styles
The coupe and convertible share this row and this piece count. Mention which you have when you call.
Material
For the 1992-1994 M30 coupe and convertible, ten 3.75" strips of polished 26 gauge 304 stainless from a USA shop go from molding to door bottom on 3M automotive-grade acrylic foam tape. QAA states the tape will hold for a lifetime without harming the Infiniti.
Molding
The top edge of each piece meets the molding. If any section is loose, cracked or missing, repair it before fitting.
Cleaning
- Wash the area below the molding and rinse.
- Strip wax and polish from the M30 with a wax-and-grease remover.
- Touch up chips or rust and let the paint cure.
- Wipe with isopropyl alcohol just before the pieces go on.
Sorting ten pieces
With no positions in the record, lay all ten out on a towel in the order the photos show, and write each position on its liner.
Fitting
Dry fit each piece with painter's tape. Check the top meets the molding and the bottom meets the door edge, then open both doors. When everything lines up, peel the liner a few inches at a time and press firmly as you go.
Later M30 pieces
Hold the M30 spacing consistent across all ten pieces.
Convertible tip
Keep the top up while the doors are open so dust stays out of the cabin.
Conditions
A mild, dry day in shade. Don't wash the car for a day.
Ordering
Tell us the year, coupe or convertible, and your readings. Hold on to the box until the work is done.
If a door reads differently
On a band this narrow, a difference of a quarter-inch on one door is worth checking. See whether that door or its molding has been replaced, and send us each reading on its own.
Work one door at a time and look along the side before starting the next.
Sort, label and dry fit every piece before any liner comes off.
Infiniti M30 buyers can reach Quality Automotive Trims at 877-752-3811; part TH92036, UPC 691821518296.
TH92036 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | TH92036 |
| UPC | 691821518296 |
| Part type | Rocker Panel Trim, Full Kit |
| Pieces in kit | 10 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 3.75" |
| Coverage / notes | Spans from the bottom of the molding to the bottom of the door |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 1992-1994 Infiniti M30 |
Fitment: TH92036
| Vehicle | Years | Body style |
|---|---|---|
| Infiniti M30 | 1992-1994 | 2-door, Coupe, Convertible |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 1992-1994 Infiniti M30
- TH92035: 6-piece Rocker Panel Trim, Full Kit
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Rocker Panel Trim, Full Kit
- Unpack all 10 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: TH92036 Rocker Panel Trim, Full Kit
Which M30 does TH92036 fit?
The 1992-1994 Infiniti M30, coupe or convertible.
How is it different from TH92035?
TH92035 has 6 pieces and is noted "between the wheel wells only." This kit has 10 pieces and no length note.
How wide is it?
3.75".
How many pieces?
Ten.
