Product Description
Nissan Sentra 1991-1995 Coupe Full Rocker Kit TH91574, No Molding, 9.25", 6 Pieces
TH91574 is the "No molding" Full Kit for the 1991-1995 Nissan Sentra 2-door coupe: six polished stainless steel pieces with a listed width of 9.25". The width bullet reads "9.25" Width, No molding." The note for this coupe kit says no molding.
The conflict in the record
The placement note on this listing says the kit "Spans from the bottom of the molding to the bottom of the door," the same as its "with molding" partner. On a car without a molding, the record doesn't say what the top edge lines up with. Before ordering:
- Check the product photos for where the top edge sits
- Measure 9.25" up from the door bottom and mark it with masking tape
- Call 877-752-3811 with a photo of the side
The two coupe kits
TH91573 is the "with molding" kit at 6.5", also six pieces. The difference in width between the two is close to three inches. If your doors have a molding, that's the listing the record points to.
A tall piece
Each piece covers 9.25" of height, so the band of paint under the tape is wide. Prepare all of it, not just the edges.
Material
The 1991-1995 Sentra coupe without molding takes six 9.25" strips that QAA forms in the USA out of polished 26 gauge 304 stainless, secured with 3M automotive-grade acrylic foam tape. That tape, QAA says, will hold for a lifetime and leaves the Nissan unmarked.
Surface prep
- Wash and rinse the whole lower door.
- Lift wax and polish off the Sentra with a wax-and-grease remover.
- Where a molding has come off, clean away its adhesive and repair any marks.
- Repair chips or rust, and alcohol-wipe each spot as its piece goes on.
Six pieces
The record doesn't list positions. Match each piece to the photos and label its liner.
Dry fit
Tape each piece in place with painter's tape, bottom edge on the door bottom, and check the top edge runs level along the door. Open both doors.
Bonding
Peel a section of liner, press across the full height, and continue. Finish with firm pressure.
After the first door
Keep the spacing the same between every pair of pieces.
Conditions
Shade, mild weather and dry; the coupe stays unwashed for a day.
Ordering
Send the year and a photo of the side. Keep the box and liners until every piece is on.
Sedan buyers
The Sentra sedan has its own "No molding" listing with a different piece count and year range. It isn't linked here, so call us if you have the sedan.
One door first
Fit a single door, step back and look along the side from the front and rear, then carry on. With no molding to work to, the dry fit matters even more, so take your time over it and check that the top edge sits level.
Keep every liner on until both doors have been dry fitted and you are happy with where the top edge sits on each.
Sentra coupe kit TH91574, UPC 691821453863: call Quality Automotive Trims at 877-752-3811.
TH91574 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | TH91574 |
| UPC | 691821453863 |
| Part type | Rocker Panel Trim, Full Kit |
| Pieces in kit | 6 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 9.25" |
| Coverage / notes | No molding; Spans from the bottom of the molding to the bottom of the door |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 1991-1995 Nissan Sentra |
Fitment: TH91574
| Vehicle | Years | Body style |
|---|---|---|
| Nissan Sentra | 1991-1995 | 2-door, Coupe |
Fitment is listed exactly as QAA catalogs it. Confirm the body style as well as the year and model. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 1991-1995 Nissan Sentra
- TH91573: 6-piece Rocker Panel Trim, Full Kit
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Rocker Panel Trim, Full Kit
- Unpack all 6 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: TH91574 Rocker Panel Trim, Full Kit
Which Sentra does TH91574 fit?
The 1991-1995 Nissan Sentra 2-door coupe, listed for "No molding."
Where does the top edge sit?
The record doesn't say for a car without molding. Check the photos or call 877-752-3811.
How wide is it?
9.25".
How many pieces?
Six.
