Product Description
TH91575 Nissan Sentra 1991-1994 Sedan Full Rocker Kit, With Molding, 6.5", 8 Pieces
For the 1991-1994 Nissan Sentra 4-door sedan, TH91575 is the "with molding" Full Kit. It has eight polished stainless steel pieces, the width bullet reads "6.5" Width, with molding," and the placement note says it "Spans from the bottom of the molding to the bottom of the door."
Start by looking at your doors
Two Full Kits are listed for the sedan, and the deciding question is simple: does your car have a molding along the doors?
- Yes: this kit, 6.5", 8 pieces.
- No: TH91576, listed "No molding," 9.25", 8 pieces.
If the molding is there on some doors but missing on others, call 877-752-3811 before ordering either.
Measuring
Read from the molding's lower edge to the bottom of the door at the front and rear of all four doors. Compare each reading with 6.5". Write them down; they're the first thing we'll ask for if you call.
Eight pieces on four doors
The record doesn't list positions, so sort the pieces with the photos. Labelling each liner with its spot before you peel anything keeps them from being swapped.
Material
Cut in the USA from polished 26 gauge 304 stainless, the eight 1991-1994 Sentra pieces go on between molding and door bottom with 3M automotive-grade acrylic foam tape. Per QAA, that tape will hold for a lifetime without harming the sedan.
Molding condition
The top edge of every piece meets the molding. Check that it's straight and secure on each door, and repair any loose or cracked section first.
Cleaning
- Wash and rinse the band below the molding
- Take off wax and polish with wax-and-grease remover
- Fix chipped paint or rust; let it fully cure
- Alcohol-wipe each Sentra door just before fitting
Dry fit
Tape each piece in place with painter's tape, top edge against the molding, bottom edge on the door bottom. Open each door to check the ends.
Bonding
Peel a short section of liner, press, and keep going. Finish each piece with firm pressure.
Toward the rear bumper
Hold the same spacing on every Sentra door.
Coupe owners
The coupe has its own "with molding" kit, with fewer pieces and a longer year range. It isn't linked to this sedan listing.
Conditions
Pick a shaded, mild, dry day. Wash the Sentra no sooner than a day later.
Ordering
Give us the year, confirm the sedan and the molding, and include your readings. Keep the box and liners until the job is done.
If one door reads differently
If a reading on one door stands out from the rest, check whether that door or its molding has been replaced. Send each door's figures separately, not an average. We would much rather check it with you on the phone than have a piece sit away from its edge.
Do one door first, then stand back and check the line before going on.
All four Sentra doors get a dry fit before any liner comes off.
Questions about Sentra kit TH91575 (UPC 691821254606) can go to 877-752-3811.
TH91575 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | TH91575 |
| UPC | 691821254606 |
| Part type | Rocker Panel Trim, Full Kit |
| Pieces in kit | 8 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 6.5" |
| Coverage / notes | With molding; Spans from the bottom of the molding to the bottom of the door |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 1991-1994 Nissan Sentra |
Fitment: TH91575
| Vehicle | Years | Body style |
|---|---|---|
| Nissan Sentra | 1991-1994 | 4-door, Sedan |
Fitment is listed exactly as QAA catalogs it. Confirm the body style as well as the year and model. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 1991-1994 Nissan Sentra
- TH91576: 8-piece Rocker Panel Trim, Full Kit
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Rocker Panel Trim, Full Kit
- Unpack all 8 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: TH91575 Rocker Panel Trim, Full Kit
Which Sentra does TH91575 fit?
The 1991-1994 Nissan Sentra 4-door sedan with molding.
What if my sedan has no molding?
TH91576 is listed for "No molding." Call 877-752-3811 to confirm.
How wide is it?
6.5".
How many pieces?
Eight.
