Product Description
Toyota Highlander 2020-2026 Stainless Gas Door Trim (GC70110)
If you drive a Toyota Highlander 4-door SUV from 2020 through 2026, GC70110 is the polished stainless overlay sized for its fuel door. The single Fitment row spans seven model years. The part is one piece of 304 stainless steel, 26 gauge, made in the USA, and it mounts to the fuel door with 3M automotive-grade acrylic foam tape.
It is not a replacement cap and not a replacement part. You MUST have the existing gas door to install this piece. The trim gives the Highlander's own door a stainless face and relies on that door working properly.
The tape does the work here, and QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle. It bonds to paint, so check the door before you begin. Chips around the edge, peeling or dull clear coat and blistered spots should be repaired first, and the door should shut flush. The trim installs directly over the existing surface, so no drilling is needed.
Clean the door with soapy water, rinse, and let it dry completely, then wipe it with a degreaser to remove wax and road film. Hold the trim on the closed door with the liner in place, and adjust it until the paint visible around it forms an even border. A few strips of painter's tape will mark the spot. Remove the liner, set the trim on your marks, and press it firmly over its whole face, giving it a second press after a minute. Open the door slowly to check that it swings clear. There's more detail on the Installation tab.
The Highlander sheet offers a range of matching pieces. Three pillar post sets are listed: PP70110 with four pieces, PP70111 with six, and PP70109 with eight. QAA doesn't explain what the larger sets' additional pieces cover, so the listing photos are the best guide. Those pillar sets are tagged 4-door Crossover SUV, while this gas door row says 4-door SUV; it's the same Highlander, just tagged differently. Up front, HT70110 is a one-piece hood vent trim. At the rear, LB70110 is a two-piece license bar that sits above the plate, LP70110 is a one-piece license plate bezel, and RD70110 is a one-piece rear deck accent. WP70110 and WP70111 are cross-listed by number only, so check their own listings.
The polished 304 surface reflects light brightly, and the thin 26 gauge sheet sits low against the door. Choose dry, moderate weather for the install and let the tape cure overnight before the first wash. Care is mild soap and a soft cloth; wipe off fuel drips after filling so they don't dry on the polished face of the Highlander's trim.
A gas door trim is a single flat part with nothing to match, so it makes a good first piece if you're planning more stainless on the Highlander. Questions? Call Quality Automotive Trims at 877-752-3811 and mention GC70110. The UPC is on the Specs tab.
GC70110 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | GC70110 |
| UPC | 840251601669 |
| Part type | Gas Door Cover Trim |
| Pieces in kit | 1 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2020-2026 Toyota Highlander |
| Not included | This is NOT a replacement gas cap or door; your existing gas door is required |
Fitment: GC70110
| Vehicle | Years | Body style |
|---|---|---|
| Toyota Highlander | 2020-2026 | 4-door, SUV |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2020-2026 Toyota Highlander
- PP70110: 4-piece Pillar Post Trim
- PP70111: 6-piece Pillar Post Trim
- PP70109: 8-piece Pillar Post Trim
- HT70110: 1-piece Hood Vent Trim
- LB70110: 2-piece License Plate Bar Accent
- LP70110: 1-piece License Plate Bezel
- RD70110: 1-piece Rear Deck Accent
- WP70110: 14-piece Window Trim Package
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Gas Door Cover Trim
- Confirm your vehicle still has its original gas door. This trim mounts over it and does not replace it.
- Unpack the piece and hold it in position to confirm the fit before mounting it.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Step back and check alignment before pressing along the full length of the piece.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: GC70110 Gas Door Cover Trim
Is GC70110 a replacement gas door?
No. It is not a replacement cap or replacement part. You MUST have the existing gas door to install this piece.
Which Highlander years fit?
The 2020-2026 Toyota Highlander 4-door SUV.
What is it made of?
Polished 304 stainless steel, 26 gauge, made in the USA.
Is drilling needed?
No. It installs directly over the existing surface with 3M automotive-grade acrylic foam tape.
How long does the tape hold?
QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
Which pillar post sets are available?
PP70110 (4 pieces), PP70111 (6 pieces) and PP70109 (8 pieces).
