Product Description
Ford Fusion Sedan 2010-2012 Stainless Front Vent Surround, 2 Pieces (FV50390)
FV50390 is a front vent surround listed for the Ford Fusion from 2010 through 2012. It's a pair of polished stainless surrounds for the 4-door Fusion, made in the USA from 304 stainless steel at 26 gauge. Both mount with 3M automotive-grade acrylic foam tape.
Check the years
The single fitment row reads Ford Fusion, 2010-2012, 4-door Sedan. Fusion sedans outside those three years aren't covered by this listing. The Fitment tab shows the row.
Surround style
The bullet describes the design as a "Surround," meaning it frames the vent opening. There are two pieces, and no dimensions are listed. The product photos show the shape; compare them with the front of your Fusion, and call us if you'd like a second opinion.
Fusion trim on this sheet
- ML50390, a two-piece set of front marker light surround rings.
- MI50390, a four-piece body molding insert kit at 1.
- LB50390, a license bar for above the plate.
- LP50390, a license plate bezel.
- RB50390, a one-piece rear bumper accent.
The marker light rings are the natural partner for the vent surrounds, since both are at the front.
Steel
Polished 304 stainless, 26 gauge. Bright from polishing, not plating.
Mounting
Both surrounds install directly over the existing surface with no drilling. QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
Prep
Around vent openings, grime and wax collect on the edges where a surround will sit. Wash with a soft brush, rinse, and wipe each mounting surface with degreaser until a clean cloth shows nothing. Use swabs for the tight spots. Dry fully.
Fitting a frame
Set the surround around the opening with the liner still on. Look for an even gap on every side, and adjust until it's consistent. Mark a few points with painter's tape. Peel, align with the marks, and press firmly all the way around. Repeat the press after a minute. Do the second piece to match. The Installation tab has full prep.
Why surrounds
Framing the vents in polished steel sharpens the front end while leaving the vents themselves alone.
Before buying
Confirm a 2010-2012 Fusion sedan. Compare the photos to your vents. If you want the marker light rings too, order them together and install in one session.
Rings and surrounds together
Marker light rings follow the round shape of the light, so they're quick to place. Doing them first gets you comfortable with the tape before you move to the vent surrounds, which take a bit more care to center. Clean every mounting surface at the same time, so the whole front is prepped in one pass.
A second look
After both surrounds are on, step well back and view the car from straight ahead and from each front corner. Small differences show up from an angle more than straight on.
Install conditions
Mild, dry day out of direct sun; keep the car dry overnight.
Care
Mild soap, soft brush.
Questions
Call Quality Automotive Trims at 877-752-3811 and mention FV50390. The UPC is on the Specs tab.
FV50390 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | FV50390 |
| UPC | 691821468614 |
| Part type | Front Vent Trim |
| Pieces in kit | 2 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2010-2012 Ford Fusion |
Fitment: FV50390
| Vehicle | Years | Body style |
|---|---|---|
| Ford Fusion | 2010-2012 | 4-door, Sedan |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2010-2012 Ford Fusion
- LB50390: 1-piece License Bar, Above plate accent Trim
- LP50390: 1-piece License Plate Bezel
- MI50390: 4-piece Body Molding Insert Trim Kit
- ML50390: 2-piece Accent Trim
- RB50390: 1-piece Rear Bumper Trim Accent
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Front Vent Trim
- Unpack all 2 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: FV50390 Front Vent Trim
What does FV50390 fit?
The 2010-2012 Ford Fusion 4-door sedan.
How many pieces?
Two surround pieces.
Is there matching front trim?
Yes. ML50390 front marker light surround rings are listed for the same Fusion.
What is it made of?
Polished 304 stainless steel, 26 gauge, made in the USA.
Does it need drilling?
No. It installs directly over the existing surface with 3M automotive-grade acrylic foam tape.
How long does the tape hold?
QAA states the tape will hold for a lifetime without causing any damage to the surface of the vehicle.
