Product Description
Ford Fusion Sedan 2010-2012 Stainless Steel Molding Insert Kit, 1 Inch (MI50390)
MI50390 is a short-run kit: three model years of the Ford Fusion 4-door sedan, 2010, 2011 and 2012. It brings four polished 304 stainless strips at 1 inch wide to lay over the sedan's body side moldings, mounted with 3M tape.
Check your year carefully
With only three years listed, the year check matters. Your records both show it. A Fusion outside 2010 to 2012 isn't covered by this row, and the title gives the same range. If you're unsure, Quality Automotive Trims can help at 877-752-3811; mention MI50390.
Then check the moldings
The strips sit on top of the existing moldings. Look at each one: present, firmly attached, no cracks, no leftover adhesive, and a profile similar to the photos. Measure the flat face of one with a ruler and compare it with 1 inch. The record doesn't say which strip goes on which door, so the photos are your layout guide too.
Material and mounting
Each strip is 26 gauge 304 stainless steel with a polished finish, made in the USA. Mounting is 3M automotive-grade acrylic foam tape, directly over the existing surface, so no drilling is needed.
Laying out four strips
Before any liner comes off, put the four strips on a towel next to the photos and match each one to a door. Write the position on the liner with a marker. It takes a minute and prevents a strip ending up on the wrong door halfway through.
Install
A dry, mild day is best; the Installation tab gives the temperature range. Wash the moldings with soap and water, dry them, and wipe them with rubbing alcohol. Number the four liners. Hold each strip in place with the liner on, center it on the molding, and mark both ends with painter's tape. Peel, set the strip on the marks, and press firmly from end to end. Step back after each one and check that the strips line up.
Other Fusion sedan parts
Five more parts are linked to the sedan tag. FV50390 is a 2-piece front vent trim. LB50390 is a 1-piece license bar, an above-plate accent trim, and LP50390 a 1-piece license plate bezel. ML50390 is a 2-piece accent trim described as front marker light surround rings. RB50390 is a 1-piece rear bumper trim accent. Each has its own page and photos, and none of them is part of this kit.
Keeping the line straight
During the dry fit, measure from the top edge of the molding to the top edge of the strip at both ends. If the two numbers match, the strip is level with the molding. Doing this on each door keeps the four strips reading as one line on the sedan.
Care
A soft cloth with mild soap and water keeps the Fusion's four inserts bright; skip steel wool and abrasive pads. After fitting, keep the car out of rain and away from its first wash for a while. Questions? Phone 877-752-3811.
MI50390 specifications
| Brand | QAA |
|---|---|
| Part number (MPN) | MI50390 |
| UPC | 691821508129 |
| Part type | Body Molding Insert Trim Kit |
| Pieces in kit | 4 |
| Material | Polished 26-gauge 304 stainless steel |
| Finish | Polished to a mirror shine |
| Width | 1" |
| Mounting | 3M automotive-grade acrylic foam tape; installs directly over the existing surface |
| Origin | Made in the USA |
| Fits | 2010-2012 Ford Fusion |
Fitment: MI50390
| Vehicle | Years | Body style |
|---|---|---|
| Ford Fusion | 2010-2012 | 4-door, Sedan |
Match the year, model, and body style in this table to your vehicle before ordering. Questions? Call Quality Automotive Trims at 877-752-3811 with your year, make, model, and body style.
Other QAA trim cataloged for the 2010-2012 Ford Fusion
- FV50390: 2-piece Front Vent Trim
- LB50390: 1-piece License Bar, Above plate accent Trim
- LP50390: 1-piece License Plate Bezel
- ML50390: 2-piece Accent Trim
- RB50390: 1-piece Rear Bumper Trim Accent
Check the body style on each listing; some kits are specific to one body style.
Installation tips: Body Molding Insert Trim Kit
- Unpack all 4 pieces and match each one to its position on the vehicle, using the product photos, before fitting any of them.
- Each piece mounts with 3M automotive-grade acrylic foam tape, so clean and dry the mounting surface first; the tape needs paint or trim free of dirt and wax.
- Align the piece and press it firmly into place directly over the existing surface, working along its full length so the tape bonds evenly.
- Fit one piece at a time and compare each with the product photos and the pieces already in place.
These are general tips. Follow any instructions packed with your kit if they differ.
FAQ: MI50390 Body Molding Insert Trim Kit
What years of Fusion does MI50390 fit?
The Ford Fusion 4-door sedan, 2010 through 2012.
How many strips are included?
Four, each 1 inch wide.
Do I need to drill?
No. It mounts with 3M automotive-grade acrylic foam tape directly over the existing surface.
What's the material?
Polished 304 stainless steel, 26 gauge, made in the USA.
Are the marker light rings included?
No. ML50390 is a separate 2-piece listing.
